Skip to content
become a verified vendor

Coverage

Precast Industries — Everything Precast
Precast/Prestressed Concrete InstituteNational Precast Concrete AssociationAmerican Concrete Pipe AssociationConcrete Masonry & Hardscapes AssociationNortheast Precast Concrete AssociationPacific Northwest Precast Concrete AssociationCalifornia Precast Concrete AssociationTexas Concrete Products AssociationOhio Precast Concrete AssociationPrecast Concrete Association of New YorkNew Jersey Precast Concrete AssociationPennsylvania Precast AssociationPennsylvania Aggregates and Concrete AssociationPrecast Concrete Association of VirginiaPrecast Tank Association of VirginiaWisconsin Precast Concrete AssociationMichigan Concrete AssociationKentucky Concrete AssociationAlabama Concrete Industries AssociationFlorida Concrete & Products AssociationFlorida Prestressed Concrete AssociationPrecast Concrete Structures Association of FloridaCarolinas Concrete Pipe and Products AssociationPCI Georgia/CarolinasPrecast of MaineCAPCA PrecastAPAPrecast/Prestressed Concrete InstituteNational Precast Concrete AssociationAmerican Concrete Pipe AssociationConcrete Masonry & Hardscapes AssociationNortheast Precast Concrete AssociationPacific Northwest Precast Concrete AssociationCalifornia Precast Concrete AssociationTexas Concrete Products AssociationOhio Precast Concrete AssociationPrecast Concrete Association of New YorkNew Jersey Precast Concrete AssociationPennsylvania Precast AssociationPennsylvania Aggregates and Concrete AssociationPrecast Concrete Association of VirginiaPrecast Tank Association of VirginiaWisconsin Precast Concrete AssociationMichigan Concrete AssociationKentucky Concrete AssociationAlabama Concrete Industries AssociationFlorida Concrete & Products AssociationFlorida Prestressed Concrete AssociationPrecast Concrete Structures Association of FloridaCarolinas Concrete Pipe and Products AssociationPCI Georgia/CarolinasPrecast of MaineCAPCA PrecastAPA
Manholes & Risers

Manhole riser Ø1200

Sanitary riser section with integral step irons and a rubber-ring joint, cast to ASTM C478 and stocked in four heights.

Standard
ASTM C478
Load class
HS-25
Lead time
12 working days
Price
$450.00
Stacked precast manhole rings in the yard, socket ends uppermostVerified listing1 / 5

Specification

Internal diameter
1200 mm
Wall thickness
125 mm
Heights
300 / 600 / 900 / 1200 mm
Joint
Rubber ring to ASTM C443
Concrete
C40/50, 4000 psi
Reinforcement
Single cage, epoxy-coated

Attached documents

Free to download. No email wall on technical data.

Four heights, one joint.

A sanitary manhole riser of 1200 mm internal diameter, cast to ASTM C478 with integral step irons and a rubber-ring joint. Stocked in four heights so a chamber can be built up to the depth a drawing calls for.

  • Rubber-ring joint — The joint is made to ASTM C443, seated on the socket so sections seal against each other without an applied sealant.
  • Integral step irons — Step irons are cast into the wall rather than drilled in afterwards, set on a consistent pitch through the stack.
  • Four stock heights — 300, 600, 900 and 1200 mm sections combine to reach chamber depth without a special pour.
  • Epoxy-coated cage — A single reinforcement cage, epoxy-coated, in C40/50 concrete at a 125 mm wall thickness.

The mould cycle

Riser sections come off a ring mould that closes, fills and strips on a fixed cycle. Wall thickness and joint geometry are set by the mould, not by the operator.

Loading out

Rings load on a flatbed and travel strapped upright. Lifting is by the cast-in anchors, and sections should not be rolled on the socket.

In use

Typical placements for a 1200 mm sanitary riser and how sections are handled getting there.

Sanitary sewer chambers

Stacked on a base unit to reach invert depth, with the rubber-ring joint made up as each section lands.

Yard storage

Held in four heights in the yard so a chamber schedule can be picked and loaded in one movement.

Delivery to site

Loaded upright and strapped for road transport, sequenced so the first section off is the first one set.

FAQs

300, 600, 900 and 1200 mm. These are combined to build a chamber to depth rather than casting a one-off section.

A rubber-ring joint to ASTM C443, seated in the socket. No applied sealant is required to make the joint.

Yes, they are cast in as part of the section rather than drilled and fixed after stripping.

HS-25, with the load calculation issued as a supporting document alongside the shop drawing.

Yes, an RFA object is supplied in the document set together with the shop drawing and mill certificate.